Conbee: Difference between revisions
From DWIKI
m (→FAQ) |
|||
| (10 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Howto= | | ||
= Links = | |||
*[https://phoscon.de/en/app/doc Phoscon documentation] | |||
*[https://www.domoticz.com/wiki/Zigbee2MQTT Installing software] | |||
*[https://flemmingss.com/how-to-set-up-deconz-and-phoscon-on-a-raspberry-pi-and-control-all-your-zigbee-devices/ https://flemmingss.com/how-to-set-up-deconz-and-phoscon-on-a-raspberry-pi-and-control-all-your-zigbee-devices/] | |||
*[https://gathering.tweakers.net/forum/list_messages/1901854 deCONZ - Zigbee gateway van Dresden Elektronik] | |||
*[https://phoscon.de/en/conbee2/compatible conbee2 compatibility list (outdated)] | |||
*[https://github.com/dresden-elektronik/deconz-rest-plugin/wiki/Supported-Devices Conbee Supported Devices] | |||
= Howto = | |||
Connecting Conbee 2 | Connecting Conbee 2 | ||
Steps: | Steps: | ||
https://phoscon.de/en/conbee/install | [https://phoscon.de/en/conbee/install https://phoscon.de/en/conbee/install] | ||
[https://github.com/Smanar/Domoticz-deCONZ https://github.com/Smanar/Domoticz-deCONZ] | |||
| |||
= Configuration = | |||
/lib/systemd/system/deconz* /usr/share/deCONZ/zcl/general.xml | |||
== Change ports == | |||
#/etc/systemd/system/deconz.service.d/override.conf | |||
/ | |||
[Service] | [Service] | ||
ExecStart= | ExecStart= | ||
ExecStart=/usr/bin/deCONZ -platform minimal --http-port=8080 --ws-port=8081 --auto-connect=1 --dbg-error=1 | ExecStart=/usr/bin/deCONZ -platform minimal --http-port=8080 --ws-port=8081 --auto-connect=1 --dbg-error=1 | ||
| |||
| |||
= FAQ = | |||
== ExecStart=/usr/bin/deCONZ -platform minimal --http-port=80 -debug-error=1 (code=exited, status=218/CAPABILITIES) == | |||
A systemd problem, fix/override of deconz.service works for me | A systemd problem, fix/override of deconz.service works for me | ||
| |||
== Sensor not reachable == | |||
After a reboot phoscon sometimes reports sensor not reachable. First thing to try is press button on the sensor. | After a reboot phoscon sometimes reports sensor not reachable. First thing to try is press button on the sensor. | ||
| |||
== Connecting Innr SP120 == | |||
In Phoscon interface that's under Devices->Lights "add new light", not a switch! | In Phoscon interface that's under Devices->Lights "add new light", not a switch! | ||
| |||
| |||
== Xiaomi smart plug == | |||
found as LUMI, lumi.plug.mmeu01, ZNCZ04LM | |||
[https://github.com/dresden-elektronik/deconz-rest-plugin/issues/2583 https://github.com/dresden-elektronik/deconz-rest-plugin/issues/2583] | |||
Leds: | |||
*red blinking fast: overheat | |||
*red blink slowly: not connected | |||
*blue on: working | |||
*blue blinking: connecting | |||
== GUI says "not connected" == | |||
Most likely because service 'deconz' is already running. Try | |||
systemctl stop deconz.service | systemctl stop deconz.service | ||
==reconnecting a sensor== | |||
Just "Add new sensor" should work | |||
==Pairing IKEA lightbulb== | |||
Switch on, then off/on 6 times with 1 second intervals, leave on after 6th time. | |||
The light should dim/brighten a bit. Then run "add new lights". | |||
Latest revision as of 20:37, 13 January 2024
Links
- Phoscon documentation
- Installing software
- https://flemmingss.com/how-to-set-up-deconz-and-phoscon-on-a-raspberry-pi-and-control-all-your-zigbee-devices/
- deCONZ - Zigbee gateway van Dresden Elektronik
- conbee2 compatibility list (outdated)
- Conbee Supported Devices
Howto
Connecting Conbee 2
Steps:
https://phoscon.de/en/conbee/install
https://github.com/Smanar/Domoticz-deCONZ
Configuration
/lib/systemd/system/deconz* /usr/share/deCONZ/zcl/general.xml
Change ports
- /etc/systemd/system/deconz.service.d/override.conf
[Service] ExecStart= ExecStart=/usr/bin/deCONZ -platform minimal --http-port=8080 --ws-port=8081 --auto-connect=1 --dbg-error=1
FAQ
ExecStart=/usr/bin/deCONZ -platform minimal --http-port=80 -debug-error=1 (code=exited, status=218/CAPABILITIES)
A systemd problem, fix/override of deconz.service works for me
Sensor not reachable
After a reboot phoscon sometimes reports sensor not reachable. First thing to try is press button on the sensor.
Connecting Innr SP120
In Phoscon interface that's under Devices->Lights "add new light", not a switch!
Xiaomi smart plug
found as LUMI, lumi.plug.mmeu01, ZNCZ04LM
https://github.com/dresden-elektronik/deconz-rest-plugin/issues/2583
Leds:
- red blinking fast: overheat
- red blink slowly: not connected
- blue on: working
- blue blinking: connecting
GUI says "not connected"
Most likely because service 'deconz' is already running. Try
systemctl stop deconz.service
reconnecting a sensor
Just "Add new sensor" should work
Pairing IKEA lightbulb
Switch on, then off/on 6 times with 1 second intervals, leave on after 6th time. The light should dim/brighten a bit. Then run "add new lights".
