Vmware: Difference between revisions
From DWIKI
m (→FAQ) |
m (→FAQ) |
||
| (14 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Links= | =Links= | ||
*https://www.altaro.com/vmware/top-20-esxcli-commands/ | |||
*[https://kb.vmware.com/s/article/1030381 Understanding SCSI device/target NMP errors/conditions in ESX/ESXi 4.x and ESXi 5.x/6.0 (1030381)] | *[https://kb.vmware.com/s/article/1030381 Understanding SCSI device/target NMP errors/conditions in ESX/ESXi 4.x and ESXi 5.x/6.0 (1030381)] | ||
*[https://www.vmguru.com/2015/12/best-practices-running-vmware-with-nfs/ Best Practices running VMware with NFS] | *[https://www.vmguru.com/2015/12/best-practices-running-vmware-with-nfs/ Best Practices running VMware with NFS] | ||
=FAQ= | =FAQ= | ||
==Mount vmfs in linux== | |||
==Cloning on command line== | ==Cloning on command line== | ||
Used vmkfstool and create new VM using "Use existing virtual disk" | Used vmkfstool and create new VM using "Use existing virtual disk" | ||
| Line 9: | Line 13: | ||
==Info== | ==Info== | ||
esxtop | esxtop | ||
==SNMP== | |||
*https://blogs.vmware.com/vsphere/2012/11/configuring-snmp-v1v2cv3-using-esxcli-5-1.html | |||
*https://docs.vmware.com/en/VMware-vSphere/6.0/com.vmware.vsphere.vcenterhost.doc/GUID-8D52E028-885A-4FE3-A00B-5403991D725D.html | |||
*https://computingforgeeks.com/how-to-monitor-vmware-esxi-host-using-librenms/ | |||
esxcli system snmp set --communities public | |||
esxcli system snmp set --target <server ip>@161/public | |||
esxcli system snmp set --enable true | |||
===snmpd has not been enabled=== | |||
Means the GUI is stupid | |||
esxcli system snmp set --communities public | |||
esxcli system snmp get | |||
https://serenity-networks.com/how-to-enable-snmp-on-esxi-5-5-5-6-for-remote-monitoring/ | |||
===snmpd: No library available for additional MIBs: No such file or directory=== | |||
===snmpd: No library available for plugin VS support=== | |||
===Error: Unknown command or namespace system snmp set –communities public=== | |||
because it's a mess | |||
===Must first configure at least one v1|v2c|v3 trap target=== | |||
===Error: Unknown command or namespace systen snmp test=== | |||
another secret | |||
==Remount nfs== | ==Remount nfs== | ||
| Line 20: | Line 58: | ||
==Network configuration== | ==Network configuration== | ||
https://www.altaro.com/vmware/vsphere-networking-basics-part-1/ | https://www.altaro.com/vmware/vsphere-networking-basics-part-1/ | ||
== Show network addresses == | |||
esxcli network ip interface ipv4 get | |||
== Show network interfaces == | |||
esxcli network ip interface list | |||
==Set network address== | |||
esxcli network ip interface ipv4 set -i vmk0 -t static --ipv4=192.168.12.11 -N 255.255.255.0 | |||
==Show hardware info== | |||
esxcli hardware pci list | |||
==Show routing table== | ==Show routing table== | ||
esxcli network ip route ipv4 list | esxcli network ip route ipv4 list | ||
==Show VM information== | |||
vim-cmd vmsvc/getallvms | |||
vim-cmd vmsvc/get.guest <vmid> | |||
==Start VM from commandline== | |||
Esx4/5/6.0 | |||
vim-cmd vmsvc/getallvms | |||
vim-cmd vmsvc/power.on <vmid> | |||
==List network interfaces== | |||
esxcfg-nics -l | |||
[[Category:Virtualization]] | |||
Latest revision as of 09:21, 31 October 2023
Links
- https://www.altaro.com/vmware/top-20-esxcli-commands/
- Understanding SCSI device/target NMP errors/conditions in ESX/ESXi 4.x and ESXi 5.x/6.0 (1030381)
- Best Practices running VMware with NFS
FAQ
Mount vmfs in linux
Cloning on command line
Used vmkfstool and create new VM using "Use existing virtual disk"
Info
esxtop
SNMP
- https://docs.vmware.com/en/VMware-vSphere/6.0/com.vmware.vsphere.vcenterhost.doc/GUID-8D52E028-885A-4FE3-A00B-5403991D725D.html
- https://computingforgeeks.com/how-to-monitor-vmware-esxi-host-using-librenms/
esxcli system snmp set --communities public esxcli system snmp set --target <server ip>@161/public esxcli system snmp set --enable true
snmpd has not been enabled
Means the GUI is stupid
esxcli system snmp set --communities public esxcli system snmp get
https://serenity-networks.com/how-to-enable-snmp-on-esxi-5-5-5-6-for-remote-monitoring/
snmpd: No library available for additional MIBs: No such file or directory
snmpd: No library available for plugin VS support
Error: Unknown command or namespace system snmp set –communities public
because it's a mess
Must first configure at least one v1|v2c|v3 trap target
Error: Unknown command or namespace systen snmp test
another secret
Remount nfs
Get system UUID
esxcli system uuid get
Network configuration
https://www.altaro.com/vmware/vsphere-networking-basics-part-1/
Show network addresses
esxcli network ip interface ipv4 get
Show network interfaces
esxcli network ip interface list
Set network address
esxcli network ip interface ipv4 set -i vmk0 -t static --ipv4=192.168.12.11 -N 255.255.255.0
Show hardware info
esxcli hardware pci list
Show routing table
esxcli network ip route ipv4 list
Show VM information
vim-cmd vmsvc/getallvms vim-cmd vmsvc/get.guest <vmid>
Start VM from commandline
Esx4/5/6.0
vim-cmd vmsvc/getallvms vim-cmd vmsvc/power.on <vmid>
List network interfaces
esxcfg-nics -l
